White Switch Hub Turned on

Jumper Cables & How To Connect Them

What are jumper cables and how to connect them? It’s an emergency, your battery has died and you’re stranded on the road. The only thing between you and oblivion is this complete stranger you’ve flagged down on the street who just so happens to own a jump starter. You could probably search online for a tutorial, but doing that might take more precious time than you have. So rather than ending up with a twisted pile of metal in a ditch, use this handy dandy illustrated steps as your Jump Starter guide. With this guide on how to connect jumper cables – you’ll be changing tires like a pro.

What Are Jumper Cables?

red and black coated wire

Long, densely insulated wires with toothy clamps on one or both ends are known as jumper cables. The clips can be identified by their color, which is often red or black to denote positive or negative polarity. The red clip indicates success. The clip in black is unfavorable.

Portable batteries called jump boxes are used with special jump cables to jumpstart vehicles. These cables link the jump battery and the dead automobile battery together. When assisting stuck autos, roadside assistance frequently uses a jump box.

How to Connect Jumper Cables to a Vehicle?

Since most people don’t have a loaded jump starter in their car, it normally takes a jump start from another car and some jumper wires to revive a dead battery. Although it isn’t difficult, you must be aware of the procedures and how to connect the cables in order to protect everyone and the vehicles.

Here is what to do:

1. Prepare the vehicles

Prior to taking any action, confirm that the battery providing the jump has sufficient voltage and is the appropriate voltage system type (12V, 6V, etc). If everything is in order, park the donor car so that it is either side by side with the recipient car or close to it. The cars must be near enough for the jumper cables to access every battery.

Execute the following now:

  • Place the two vehicles in the park or neutral.
  • Switch off the ignitions.
  • Engage the parking brake.
  • Car hoods should be opened and fastened.

2. Add the jumper cables 

Now that everything is set up, it’s time to set up the jumper wires and get your car started again.

Putting the Clips on:

  • Using the clips, fasten them to the terminals as follows:
  • Red to Dead – Join the positive (red) clip to the battery’s positive terminal on the abandoned vehicle.
  • Red to Donor – Join the positive (red) connector to the positive terminal of the other vehicle’s donor battery.
  • Black to Donor – Join the black clip to the donor car’s negative terminal.
  • Black to Metal – Join the black clip to a dead car’s painted or unpainted metal component that is not right adjacent to the battery. A good place is one of the metal struts holding the hood open.

3. Switch on the donor car

person in gray long sleeve shirt riding black motorcycle

Once everything is connected, it’s time to turn on the donor car so it can begin the dead batteries. Allow the donor car to run for a while.

4. Examine a dead battery

After a little while, inspect one of the automobiles being jumped’s interior lights. If it turns on, the battery is receiving power.

5. Restart the dead vehicle

With the flat battery, drive the engine. Perhaps all goes as planned and the car can be driven once more.

6. Release the Jumper Cable Clips

Once the car has started, unclip the jumper cables by going backward from how you attached them:

  1. The uncoated metal with the black clip.
  2. The negative terminal’s black clip.
  3. The contributor car’s red clip.
  4. The battery of the deceased car’s red clip.
  5. To recharge the battery, it’s preferable to let the car run continuously for at least 10 to 20 minutes.

What Happens If the Car Is Unable to Drive After the Jumpstart?

person holding red and black hand tool

Once the dead automobile has been charged for a few minutes, if it still won’t start, test the connections and go anew. After multiple tries, if the car won’t start, the battery can be too dead to be jump-started.

Battery Information Required to Jumpstart a Car

Car batteries feature two terminals, which are larger nubs. There is a positive terminal and a negative terminal. Each needs to be distinctively marked. To complete the circuit and recharge the dead battery, cables must connect to the proper terminal.

Positive Terminal: The positive terminal is often the larger of the two terminals. It is labeled with “POS” or “+”. It will hook to the jumper cable’s positive clip, which is typically red.

Negative Terminal: The battery’s negative terminal is typically labeled with “NEG” or “-“. To another clip, which is often black, this will fasten.

If you know how to do it and have a set of jumper cables, you should be available to perform your battery.

Essential Jumpstarting Safety Advice

  • Read the instruction handbook. Some vehicles’ sensitive wiring makes them unsuitable for jump-starting.
  • Never attempt to jump batteries that are rusty, cracked, leaking, or obviously broken.
  • Never attempt to jump-start a frozen battery.
  • Avoid attempting to jump dry batteries.
  • Keep the clips apart from one another.

Keep the donor battery safe

Follow these steps to secure the vehicle by donating a battery:

  1. Make sure the dead battery has the same voltage level as the donor battery. A 6V and a 12V, for instance, shouldn’t be used together.
  2. Join alligator clips in the proper sequence.
  3. Then check to see if the donor battery is still full.
red and black coated wire


What are the purposes of jumper cables?

Jumper cables are shielded wires that are also referred to as booster cables or jump leads. They are used to attach a car battery to that other power source so they arrive in pairs with alligator clips. These supplies might either be batteries with the same power as the car that gets to be jumpstarted or other moving cars.

Are jumper cables available at petrol stations?

Small cables might be sold at gas stations, but they’re frequently not the greatest option. This is particularly valid if you drive a truck or SUV. You should utilize the thickest cables you can find, checking to make sure they can transmit the energy needed to kickstart your car.

What makes heavy-duty jumper cables necessary?

In order to jumpstart the car more rapidly, heavy-duty jumper wires will be thicker and have a larger gauge. This guarantees that you can jumpstart your car even in the toughest circumstances, such as when it’s freezing outside and your battery is almost completely dead.

How are jumper cables connected?

Keep in mind the cars are both off before continuing. Then, join the red clamp to the dead battery’s positive terminal, which is frequently denoted by a “+” symbol. Next, attach the opposite end of the red wire to the functioning battery’s positive terminal. Connect the black connector to the “donor” power source’s negative terminal. Then, connect the cable’s black connector at the opposite end to a metal component of the engine in the car that has a flat battery. Start the working automobile after the cables are in place while keeping it in the park.

Should I stop my car before unplugging the jumper cables?

Yes, Keep your hands off the cords if your car is running. Before connecting or disconnecting, it is necessary to turn off both the vehicle and the auxiliary supply. If not, it might harm a vehicle and even electrocute someone.

Wrapping Up

Make sure that you know how to connect jumper cables before trying to jumpstart a car or truck. Always follow standard safety procedures when using jumper cables to prevent injury, and never attempt to charge a battery that is too large or too small for your car. Last but not least, always wear protective clothing while using jumper cables, as the exposed metal prongs can conduct electricity in ways that you might not expect.

What do you think?

Written by webmaster_kzwort

Free stock photo of action, asphalt, blur

The Price Of Maruti Alto 800 In 2022

How To Remove Tint From Car Windows

How To Remove Tint From Car Windows